ÃÛÌÒÓ°Ïñ

architecture - engineering - construction
ÃÛÌÒÓ°Ïñ

Kingspan Insulation plays key role in Kennesaw State University's impressive new student center

 

The bright, modern building offers 174,000 square feet of indoor space as well as an outdoor pool, two sand volleyball courts and a basketball court. Inside, visitors find courts for basketball, volleyball, racquetball and more, 8-lane pool, tracks for walking, jogging and running, fitness studios, climbing wall, tennis complex with hitting wall, weight training and conditioning areas, multipurpose rooms, and fully equipped locker rooms.

With a budget of $38.7 million, the Dr. Betty L. Siegel Center replaces an earlier 55,000-square-foot facility that opened in 1967. One of the highest priorities in building the new facility was sustainability, both in the materials used and the energy performance, all with the goal of minimizing its carbon footprint. The project architect and builder selected materials that would best contribute to that goal.

One of the key components in the wall construction is the use of Kingspan GreenGuard Type IV 25 PSI XPS Insulation Board from Kingspan Insulation. The two-story building features masonry framing with a brick exterior, and the Kingspan GreenGuard XPS Insulation Board provides the ideal exterior insulation performance for this cavity wall application.

Extruded polystyrene (XPS) provides superior moisture resistance, and because it does not absorb moisture, it retains its insulating properties over time. With an R-Value of 5.0 per inch of thickness, the board increases energy efficiency while offering the advantage of being lightweight, easy to handle, and easy to cut with a knife. In this application at KSU, the board is two inches thick for an R-10 value, which exceeds the code requirement for the area.

The Dr. Betty L. Siegel Center is constructed with a concrete block base covered by a fluid-applied membrane. Brick ties from the block extend out to the brick, and the Kingspan GreenGuard XPS Insulation Board is friction fit between the brick ties with an adhesive on the back that helps strengthen the bond between the board and the fluid layer. Two inches of dead space between the insulation board and the brick allows for drainage and ventilation that enhances the performance and further eliminates moisture issues.

Construction of the dramatic new facility began in late 2013 and took about 18 months. Since its official opening and dedication, the Dr. Betty L. Siegel Student Recreation and Activities Center has become one of the key buildings on campus and is performing as planned. Every exterior brick wall on the building features the Kingspan GreenGuard Type IV 25 PSI XPS Insulation Board underneath, ensuring that it will deliver many years of enjoyment for students and faculty at KSU.

@KingspanIns_US #KingspanIns_US #Kingspan #Insulation #MoistureManagement

For other relevant searches, you might want to try:

(03 52 00) Lightweight Concrete Roof Insulation
(03 52 13) Composite Concrete Roof Insulation
(04 27 00) Multiple-Wythe Unit Masonry
(04 28 00) Concrete Form Masonry Units
(05 34 00) Acoustical Metal Decking
(07 20 00) Thermal Protection
(07 21 00) Thermal Insulation
(07 21 13) Board Insulation
(07 21 13.13) Foam Board Insulation
(07 21 13.16) Fibrous Board Insulation
(07 21 13.19) Mineral Board Insulation
(07 21 16) Blanket Insulation
(07 21 19) Foamed-In-Place Insulation
(07 21 23) Loose-Fill Insulation
(07 21 26) Blown Insulation
(07 21 29) Sprayed Insulation
(07 21 53) Reflective Insulation
(07 22 00) Roof and Deck Insulation
(07 22 16) Roof Board Insulation
(07 24 00) Exterior Insulation and Finish Systems
(07 24 13) Polymer-Based Exterior Insulation and Finish System
(07 24 16) Polymer-Modified Exterior Insulation and Finish System
(07 24 19) Water-Drainage Exterior Insulation and Finish System
(07 40 00) Roofing and Siding Panels
(07 41 00) Roof Panels
(07 42 00) Wall Panels
(07 44 00) Faced Panels
(07 46 00) Siding
(07 50 00) Membrane Roofing
(07 55 00) Protected Membrane Roofing
(07 62 00) Sheet Metal Flashing and Trim
(07 65 00) Flexible Flashing
(07 76 00) Roof Pavers
(09 20 00) Plaster and Gypsum Board
(09 80 00) Acoustic Treatment
(09 81 00) Acoustic Insulation
(09 81 13) Acoustic Board Insulation
(09 81 16) Acoustic Blanket Insulation
(09 81 29) Sprayed Acoustic Insulation
(10 71 00) Exterior Protection
(21 07 00) Fire Suppression Systems Insulation
(21 07 16) Fire-Suppression Equipment Insulation
(21 07 19) Fire-Suppression Piping Insulation
(22 07 00) Plumbing Insulation
(22 07 16) Plumbing Equipment Insulation
(22 07 19) Plumbing Piping Insulation
(23 06 00) Schedules for HVAC
(23 07 00) HVAC Insulation
(23 07 13) Duct Insulation
(23 07 16) HVAC Equipment Insulation
(23 07 19) HVAC Piping Insulation
(40 40 00) Process Piping and Equipment Protection
(40 42 00) Process Piping and Equipment Insulation
(40 42 13) Process Piping Insulation
(40 42 13.13) Cryogenic Temperature Process Piping Insulation
(40 42 13.16) Low Temperature Process Piping Insulation
(40 42 13.19) Intermediate Temperature Process Piping Insulation
(40 42 13.23) High Temperature Process Piping Insulation
(40 42 13.26) Process Piping Insulation for Specialty Applications
(40 42 23) Process Equipment Insulation
(40 42 23.13) Cryogenic Temperature Process Equipment Insulation
(40 42 23.16) Low Temperature Process Equipment Insulation
(40 42 23.19) Intermediate Temperature Process Equipment Insulation
(40 42 23.23) High Temperature Process Equipment Insulation
(40 42 23.26) Process Equipment Insulation for Specialty Applications