ÃÛÌÒÓ°Ïñ

Monitored Edge Link

The Miller Edge Model gate and door edge transmitter is designed to eliminate the need to hard wire sensing edges to motor controls. It is easily mounted and wired to the gate or door edge sensor. When the Sensing Edge comes into contact with an obstruction, a closed circuit signal is created and is sent to the transmitter. The transmitter relays the signal to the receiver that is wired to the stop or reverse terminals in the motor controls.

MEL-K20 MEL (Monitored Edge Link) Transmitter and Receiver

MEL provides a wireless transmission from a Sensing Edge to operator controls eliminating the need for hard wired coil cords or retractable reels. The MEL system includes a transmitting unit that wire to a monitored edge sensor and a receiving unit. MEL has a built-in feature to detect the presence and function of a monitored entrapment protection device. If the device detects a fault in the system, MEL features LED indicators to simplify diagnostics.

MEL-RX20 MEL (Monitored Edge Link) Receiver

MEL-RX20 receives a monitored Sensing Edge signal from the MEL-TX20 transmitter eliminating the need for hard wired coil cords or retractable reels. Operates on 12-24vAC/DC.MEL-RX20 features LED indicators for simplified diagnostics.

MEL-TX20 MEL (Monitored Edge Link) Transmitter

MEL-TX20 transmits a monitored Sensing Edge signal to the MEL-RX20 receiver eliminating the need for hard wired coil cords or retractable reels. Operates on two (2) "AA" lithium batteries and is housed in a NEMA4 enclosure.

MWRT02 Receiver and Transmitter

Includes single channel receiver (MWR02A) and transmitter (MWT02). The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.

MWRTA02 Receiver and Transmitter with Audible Low Battery Alarm

Includes single channel receiver (MWR02A) and transmitter (MWTA02) with audible low battery alarm. This feature that activates when the battery has only 25% of its life remaining, indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals. The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.

MWR02A Single Channel Receiver

The receiver will operate on either 12 or 24 volt AC or DC and provides N.O. or N.C. output. For use with MWT02 or MWTA02 transmitter.

MWTA02 Sensing Edge Transmitter

Wirelessly transmits signal to compatible receiver (MWR02A)

MWTA02 Sensing Edge Transmitter with Audible Low Battery Alarm

Includes a built in Audible Alarm feature that activates when the battery has only 25% of its life remaining, indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals. For use with MWR02 or MWR03 receiver.

MWR03 3-channel Receiver

Works with most gate and commercial door operators. The one receiver is capable of receiving signals from up to 3 different input devices.

MWHT01: Hand Held Transmitter

One button single channel remote control transmitter with visor clip. 9 switch control for easy code setting

Mini Keyfob Transmitter

Single button remote control with visor clip.

ANT-R: Rigid Antenna, Insulated

Use to increase signal reception when needed.

ANT-K: Antenna Cable

COAX Cable and connector block. Use to increase range when needed.

TB-01 Transmitter Mounting Bracket

Aluminum mounting bracket with pre-drilled holes and slots for easy mounting to 2” round posts.

MWCK04: Communicator Kit

Includes MWCKT04 edge transmitter and MWCKR04 receiver. This kit is designed to provide a fully reliable, self checking communication between the 4-wire Sensing Edge and the door or gate motor operator.

MWCT04: Communicator Transmitter

For use with MWCKR04 receiver.

MWCR04: Communicator Receiver

For use with MWCKT04 transmitter.